General
IC-F1100DT/S |
IC-F1100D |
IC-F2100DT/S |
IC-F2100D |
||
|---|---|---|---|---|---|
Frequency coverage*(*Varies according to version) |
136–174 MHz(NXDN/dPMR) |
350–400 MHz (NXDN, EXP)400–470 MHz (NXDN/dPMR, ALL)450–512 MHz (NXDN, USA)450–520 MHz (NXDN, EXP) |
|||
Number of channels |
128 channels/ 8 zones |
16 channels |
128 channels/ 8 zones |
16 channels |
|
Type of emission*(*Depending onversion) |
11K0F3E, 4K00F1D (USA) |
||||
16K0F3E, 14K0F3E, 11K0F3E, 8K50F3E, 4K00F1D (EXP) |
|||||
16K0F3E, 14K0F3E, 8K50F3E, 4K00F1D (EUR) |
|||||
Power supply requirement |
7.5V DC nominal |
||||
Current drain(approx.) |
Tx |
1.3A |
1.4A |
||
Rx |
520 mA /110 mA
|
520 mA /110 mA
|
|||
Antenna impedance |
50Ω |
||||
Operating temperature range(Radio specification) |
–30°C to +60°C; –22°F to +140°F (Radio specification)
|
||||
–25°C to +55°C (Radio specification)
|
|||||
Dimensions(W × H × D; Projections not included) |
IC-F1100DS/D, IC-F2100DS/D: 52.2 × 111.8 × 29.4 mm; 2.1 × 4.4 × 1.2 in (With BP-280)IC-F1100DT, IC-F2100DT: 52.2 × 111.8 × 34.1 mm; 2.1 × 4.4 × 1.3 in (With BP-280) |
||||
Weight (approx.) |
IC-F1100D, IC-F2100D: 260 g; 9.2 oz (With BP-280 and MB-133)
|
||||
Transmitter
IC-F1100DT/S |
IC-F1100D |
IC-F2100DT/S |
IC-F2100D |
||
|---|---|---|---|---|---|
Output power(Hi, L2, L1) |
5 W, 2 W, 1 W |
4 W, 2 W, 1 W |
|||
Maximum frequency deviation |
± 5.0 kHz (25 kHz), ±4.0 kHz (20 kHz), ±2.5 kHz (12.5 kHz) |
||||
Spurious emissions |
70 dB minimum (USA) |
||||
0.25 μW (≤ 1 GHz), 1.0 μW (> 1 GHz) (EUR/EXP) |
|||||
Frequency stability |
±1.0ppm |
||||
Audio harmonic distortion |
0.7% typ. (25 kHz),
|
||||
FM Hum and Noise(without CCITT filter) |
40 dB typical (12.5 kHz) (USA) |
44 dB typical (12.5 kHz) (USA) |
|||
Residual modulations(with CCITT filter) |
52 dB typical (25 kHz),
|
54 dB typical (25 kHz),
|
|||
External microphone connector |
3-conductor 2.5 (d) mm (1/10)/2.2 kΩ |
||||
Receiver
IC-F1100DT/S |
IC-F1100D |
IC-F2100DT/S |
IC-F2100D |
||
|---|---|---|---|---|---|
Sensitivity |
(at 12dB SINAD) |
0.21 μV typical |
0.24 μV typical |
||
(at 20dB SINAD) |
–4 dBμV typical emf |
–5 dBμV typ. emf (25/20 kHz),
|
|||
(at 5% BER) |
–8 dBμV typical emf (0.20 μV typical) |
||||
Adjacent channel selectivity |
77 dB typ. (25 kHz), 74 dB typ. (12.5 kHz), 69 dB typ. (12.5 kHz), 59 dB typ. (digital) |
76 dB typ. (25 kHz), 75 dB typ. (12.5 kHz), 69 dB typ. (12.5 kHz), 58 dB typ. (digital) |
|||
Spurious response rejection |
80 dB typical |
||||
Intermodulation rejection |
75 dB typ. (25/12.5 kHz),
|
77 dB typ. (25/12.5 kHz),
|
|||
69 dB typ. (25/20/12.5 kHz),
|
70 dB typ. (25/20/12.5 kHz), 74 dBμV emf typ. (digital) (EUR/EXP) |
||||
Hum and noise |
(With CCITT filter) |
47 dB typ. (25 kHz),
|
42 dB typical (12.5 kHz) (USA) |
||
(Without CCITT filter) |
52 dB typ. (25 kHz),
|
50 dB typ. (25 kHz),
|
|||
AF output power(at 5% distortion) |
Internal SP |
1500 mW typical (With an 8Ω load) |
|||
External SP |
400 mW typical (With an 8Ω load) |
||||
External speaker connector |
2-conductor 3.5 (d) mm (1⁄8)/8 Ω |
||||
All stated specifi cations are subject to change without notice or obligation.
Measurements made in accordance with TIA-603 (USA/EXP) or EN 300-086 (EUR).
Applicable U.S. Military Specifications
Icom makes rugged products that have been tested to and passed the following MIL-STD requirements and strict environmental standards.
Standard |
MIL-810 G |
|
|---|---|---|
Method |
Procedure |
|
Low Pressure |
500.5 |
I, II |
High Temperature |
501.5 |
I, II |
Low Temperature |
502.5 |
I, II |
Temperature Shock |
503.5 |
I-C |
Solar Radiation |
505.5 |
I |
Rain Blowing/Drip |
506.5 |
I, III |
Humidity |
507.5 |
II |
Salt Fog |
509.5 |
– |
Dust Blowing |
510.5 |
I |
Immersion |
512.5 |
I |
Vibration |
514.6 |
I |
Shock |
516.6 |
I, IV |
Also meets equivalent MIL-STD-810 -C, -D, -E and -F.
Ingress Protection Standard |
|
|---|---|
Dust & Water |
IP67/55/54 |
Reviews
There are no reviews yet.