ICOM IC-F1100DT/DS/D , F2100DT/DS/D

Category:
General
IC-F1100DT/S
IC-F1100D
IC-F2100DT/S
IC-F2100D
Frequency coverage*
(*Varies according to version)
136–174 MHz(NXDN/dPMR)
350–400 MHz (NXDN, EXP)
400–470 MHz (NXDN/dPMR, ALL)
450–512 MHz (NXDN, USA)
450–520 MHz (NXDN, EXP)
Number of channels
128 channels/ 8 zones
16 channels
128 channels/ 8 zones
16 channels
Type of emission*
(*Depending onversion)
11K0F3E, 4K00F1D (USA)
16K0F3E, 14K0F3E, 11K0F3E, 8K50F3E, 4K00F1D (EXP)
16K0F3E, 14K0F3E, 8K50F3E, 4K00F1D (EUR)
Power supply requirement
7.5V DC nominal
Current drain
(approx.)
Tx
1.3A
1.4A
Rx
520 mA /110 mA
(Max. audio (internal SP)/Standby)
520 mA /110 mA
(Max. audio (internal SP)/Standby)
Antenna impedance
50Ω
Operating temperature range
(Radio specification)
–30°C to +60°C; –22°F to +140°F (Radio specification)
(USA/EXP)
–25°C to +55°C (Radio specification)
(EUR)
Dimensions
(W × H × D; Projections not included)
IC-F1100DS/D, IC-F2100DS/D:
52.2 × 111.8 × 29.4 mm; 2.1 × 4.4 × 1.2 in (With BP-280)IC-F1100DT, IC-F2100DT:
52.2 × 111.8 × 34.1 mm; 2.1 × 4.4 × 1.3 in (With BP-280)
Weight (approx.)
IC-F1100D, IC-F2100D: 260 g; 9.2 oz (With BP-280 and MB-133)
IC-F1100DS, IC-F2100DS: 270 g; 9.5 oz (With BP-280 and MB-133)
IC-F1100DT, IC-F2100DT: 280 g; 9.9 oz (With BP-280 and MB-133)
Transmitter
IC-F1100DT/S
IC-F1100D
IC-F2100DT/S
IC-F2100D
Output power
(Hi, L2, L1)
5 W, 2 W, 1 W
4 W, 2 W, 1 W
Maximum frequency deviation
± 5.0 kHz (25 kHz), ±4.0 kHz (20 kHz), ±2.5 kHz (12.5 kHz)
Spurious emissions
70 dB minimum (USA)
0.25 μW (≤ 1 GHz), 1.0 μW (> 1 GHz) (EUR/EXP)
Frequency stability
±1.0ppm
Audio harmonic distortion
0.7% typ. (25 kHz),
0.9% typical (20 kHz),
1.0% typical (12.5 kHz)
(at AF 1 kHz 40% deviation)
FM Hum and Noise
(without CCITT filter)
40 dB typical (12.5 kHz) (USA)
44 dB typical (12.5 kHz) (USA)
Residual modulations
(with CCITT filter)
52 dB typical (25 kHz),
50 dB typical (20 kHz),
46 dB typical (12.5 kHz) (EUR/EXP)
54 dB typical (25 kHz),
52 dB typical (20 kHz),
48 dB typical (12.5 kHz) (EUR/EXP)
External microphone connector
3-conductor 2.5 (d) mm (1/10)/2.2 kΩ
Receiver
IC-F1100DT/S
IC-F1100D
IC-F2100DT/S
IC-F2100D
Sensitivity
(at 12dB SINAD)
0.21 μV typical
0.24 μV typical
(at 20dB SINAD)
–4 dBμV typical emf
–5 dBμV typ. emf (25/20 kHz),
–2 dBμV typ. emf (12.5 kHz)
(at 5% BER)
–8 dBμV typical emf (0.20 μV typical)
Adjacent channel selectivity
77 dB typ. (25 kHz),
74 dB typ. (12.5 kHz),
69 dB typ. (12.5 kHz),
59 dB typ. (digital)
76 dB typ. (25 kHz),
75 dB typ. (12.5 kHz),
69 dB typ. (12.5 kHz),
58 dB typ. (digital)
Spurious response rejection
80 dB typical
Intermodulation rejection
75 dB typ. (25/12.5 kHz),
71 dB typ. (digital)
(USA/EXP)
77 dB typ. (25/12.5 kHz),
70 dB typ. (digital)
(USA/EXP)
69 dB typ. (25/20/12.5 kHz),
74 dBμV emf typ. (digital)
(EUR)
70 dB typ. (25/20/12.5 kHz), 74 dBμV emf typ. (digital) (EUR/EXP)
Hum and noise
(With CCITT filter)
47 dB typ. (25 kHz),
43 dB typ. (12.5 kHz) (USA/EXP)
42 dB typical (12.5 kHz) (USA)
(Without CCITT filter)
52 dB typ. (25 kHz),
50 dB typ. (20 kHz),
46 dB typ. (12.5 kHz)
(EUR)
50 dB typ. (25 kHz),
48 dB typ. (20 kHz),
45 dB typ. (12.5 kHz)
(EUR)
AF output power
(at 5% distortion)
Internal SP
1500 mW typical (With an 8Ω load)
External SP
400 mW typical (With an 8Ω load)
External speaker connector
2-conductor 3.5 (d) mm (1⁄8)/8 Ω
All stated specifi cations are subject to change without notice or obligation.
Measurements made in accordance with TIA-603 (USA/EXP) or EN 300-086 (EUR).
Applicable U.S. Military Specifications
Icom makes rugged products that have been tested to and passed the following MIL-STD requirements and strict environmental standards.
Standard
MIL-810 G
Method
Procedure
Low Pressure
500.5
I, II
High Temperature
501.5
I, II
Low Temperature
502.5
I, II
Temperature Shock
503.5
I-C
Solar Radiation
505.5
I
Rain Blowing/Drip
506.5
I, III
Humidity
507.5
II
Salt Fog
509.5
Dust Blowing
510.5
I
Immersion
512.5
I
Vibration
514.6
I
Shock
516.6
I, IV
Also meets equivalent MIL-STD-810 -C, -D, -E and -F.
Ingress Protection Standard
Dust & Water
IP67/55/54

Reviews

There are no reviews yet.

Be the first to review “ICOM IC-F1100DT/DS/D , F2100DT/DS/D”

Your email address will not be published. Required fields are marked *